12 w i m a s m d m p 3 -y 2 smd metallpapier-funk- entst?rkondensatoren klasse y2 ? nach din en 132 400 / iec 60384-14/2 klasse y2. ? hoher entst?rungsgrad durch d?mpfungsarmen aufbau mit niedrigem esr. ? hohe sicherheit gegen aktive und passive entflammung. ? ausgezeichnetes regenerierverhalten. metallized paper smd rfi capacitors class y2 ? in accordance with iec 60384-14/2 class y2. ? good attenuation and low esr for high degree of interference suppression. ? particularly high reliability against active and passive flammability. ? problem-free clearing. technical data dielectric: paper, epoxy resin impregnated. capacitor electrodes: vacuum-deposited. encapsulation: flame retardent plastic case, ul 94 vC0, with epoxy resin seal. colour: black. marking: gold. temperature range: C40 ) c to +110 ) c. test specifications: in accordance with din en 132 400. test category: 40/110/56/c in accordance with iec. insulation resistance at +20 c: 12 x 10 3 m v in accordance with din en 132 400 measuring voltage: 100 v/1 min. capacitance tolerance: 20 %. maximum pulse rise time: capacitance pulse rise time v/ m sec pf max. operation 1000 1000 1500 600 2200 . . . 4700 450 in accordance with din en 132 400. dissipation factor: tan d 13 x 10 -3 at 1 khz and +20 ) c. test voltage: 2700 vdc , 2 sec. smd mp 3-y2 approvals country authority specification approval no. germany vde din en 132 400 87455 iec 60384-14/2 resistance to soldering heat: solder bath temperature max. 260 c. soldering duration max 5 sec. change in capacitance d c/c < 3 %. in accordance with din iec 60068-2-20 (test tb.). soldering process: wave soldering and re-flow soldering (see temperature/time graphs page 16). wima smd mp 3-x2 in accordance with the main catalogue 2/2000 available on request. technische angaben dielektrikum: kondensatorpapier, impr?gniert mit epoxidharz. bel?ge: aufmetallisiert. umhllung: flammhemmendes kunststoffgeh?use. ul 94 vC0, epoxidharzvergu?. farbe: schwarz. aufdruck: gold. temperaturbereich: C40 ) c bis +110 ) c. prfungen: nach din en 132 400. prfklasse: 40/110/56/c nach iec. isolationswerte bei +20 c: 12 ? 1 0 3 m v nach din en 132 400. me?spannung: 100 v/1 min. kapazit?tstoleranz: 20 %. impulsbelastung: c-wert flankensteilheit v/ m s pf max. betrieb 1000 1000 1500 600 2200 . . . 4700 450 nach din en 132 400. verlustfaktor: tan d 13 ? 10 -3 bei 1 khz und +20 ) c prfspannung: 2700 v-, 2 s. prfzeichen smd mp 3-y2 land prfstelle norm ausweis-nr. deutschland vde din en 132 400 87455 iec 60384-14/2 l?tw?rmebest?ndigkeit: temperatur des l?tbades max. 260 c. l?tdauer max. 5 s. kapazit?ts?nderung d c/c < 3 %. prfung tb nach din iec 60068-2-20. l?ttechnik: wellenl?tung und reflowl?tung (siehe temperatur/zeitdiagramm seite 16). wima smd mp 3-x2 gem?? hauptkatalog 11/99 auf anfrage lieferbar.
13 w i m a s m d m p 3 -y 2 wertebersicht / general data kapazit?t 250 vac * capacitance l w h size code 0.2 0.3 0.2 1000 pf 16.5 15.0 7.0 6560 1500 ? 16.5 15.0 7.0 6560 2200 ? 16.5 15.0 7.0 6560 3300 ? 16.5 15.0 7.0 6560 4700 ? 16.5 15.0 7.0 6560 * wechselspannungen: f = 50 hz. ac voltage: f = 50 hz. auch werte der e12-reihe lieferbar. also available in e12-values. gegurtete ausfhrung siehe seite 14. taped version see page 14. alle ma?e in mm. / dims. in mm. l?tpadempfehlung. / solder pad recommendation. abweichungen und konstruktions?nderungen vorbehalten. / rights reserved to amend design data without prior notification. h w l 0.7 0.7 6 15 2.5 klebespalt bonding slit - - 1 0 0 0 p f - - 1 5 0 0 p f - - 2 2 0 0 p f - - 3 3 0 0 p f - - 4 7 0 0 p f 1 10 100 1000 f/mhz 3 5 7 3 5 7 7 5 3 7 5 3 10 1 0.1 0.01 z scheinwiderstand in abh?ngigkeit von der frequenz (richtwerte). impedance change with frequency (general guide). kapazit?ts?nderung in abh?ngigkeit von der temperatur (f = 1 khz)) (richtwerte) capacitance change with temperature (f = 1 khz) (general guide) isolationswert in abh?ngigkeit von der temperatur (richtwerte) insulation resistance change with temperature (general guide) verlustfaktor in abh?ngigkeit von der temperatur (f = 1 khz) (richtwerte) dissipation factor change with temperature (f = 1 khz) (general guide) -55 -40 -20 0 20 40 60 80 100 t( c) m x f(s) 10 10 10 4 3 2 -55 -40 -20 0 20 40 60 80 10 0 t( c) c/c (%) 12 8 4 0 -4 -8 -12 verlustfaktor in abh?ngigkeit von der frequenz (richtwerte) dissipation factor change with frequency (general guide) tan (x 10 ) -3 -55 -40 -20 0 20 40 60 80 100 t( c) 40 36 32 28 24 20 16 12 8 4 0 tan (x 10 ) -3 10 10 10 10 10 f/hz 23 4 5 6 30 26 22 18 14 10 6 2 0
|